#CUTTING VINYL LATTICE PANELS HOW TO#
#CUTTING VINYL LATTICE PANELS INSTALL#
#CUTTING VINYL LATTICE PANELS FREE#

Porch skirting can add immense curb appeal to your home. What can I put under my deck besides lattice? This will prevent rust stains on your lattice. When installing vinyl lattice be certain to use stainless steel nails or fasteners to secure your lattice sheets. These two numbers will probably be different. At the other end of the panel (4 feet away) take a measurement from the top of the panel to the ground.

#CUTTING VINYL LATTICE PANELS INSTALL#

To install the lattice, measure vertically from the top of the panel (the bottom of the deck) to the ground. You can also use a trim saw or a handsaw. Most of the people who usually need to do it regularly, suggests using a circular saw and a sharp and new cutting blade. The best way to cut vinyl lattice is to use a circular saw and a cutting blade. How much does it cost to install lattice on a deck?.What’s the best way to cut vinyl lattice?.What can I put under my deck besides lattice?.If there's a large gap beneath the panel, add soil, then smooth it out to create a consistent space between the panel and ground. If it drags on the ground, use a shovel or rake to remove some dirt from in front of the panel. Check to make sure the panel swings up and down smoothly.Use a drill/driver to screw the hinge to the porch. Slip a pry bar under the panel and raise it up tight against the porch fascia. Screw the hinges to the frames first, then set the panels in the openings under the porch.Two hinges are sufficient for a panel that's shorter than 8 feet, but use three hinges on one that's longer. Hang the framed-lattice panels from the porch with either 3- or 4-inch strap or T-hinges.Hang the framed-lattice panels Photo by Chip Henderson Where two pieces of vinyl lattice meet at a center stile, secure the seam with two rows of 1-inch panhead screws.Ħ.Be sure to drill clearance holes slightly larger than the screw shanks so the lattice can expand and contract.ĥ. Lay the frames facedown and attach the lattice with 1-inch panhead screws driven through washers. Cut the lattice panels down to size using a sabre saw or circular saw.Size the lattice panels Photo by Chip Henderson Once the frames are assembled, apply a coat of primer, followed by two coats of gloss enamel trim paint.Ĥ.Be sure the leg of the T-shaped plate is centered on the 1x4 stile. Connect the center stile to the frame with two 4-inch T-plates.Connect the center stile, prime, and paint Photo by Chip Henderson Position the hardware pieces about ¼ of an inch from the edge of the frame and secure them with 3/4-inch-long flathead screwsģ.Strengthen the frame by installing a 6-inch mending plate and a 3½-inch flat corner brace at each corner joint. Cut the frame parts to length and assemble them facedown on a flat surface.The completed frames must be a ½-inch narrower than the overall width and 1 inch shorter than the height.Ģ. Measure the openings between the columns or posts.

Be careful that you don't damage the porch fascia or support columns.

Start by removing the old lattice from the porch with a flat pry bar.

Prep for installation Photo by Chip Henderson The techniques used here can also be adapted for replacing lattice on a deck, fence, gate, privacy screen, or trellis.

The swing-up frames also make it easy to crawl underneath the porch to repair the framing if needed. Rather than permanently attach the frames, we hung them on hinges so the homeowners could use the space below the porch for storage. We also opted for an unconventional installation method. Here we built a durable new skirt using pressure-treated lumber and TuffBilt plastic lattice. (The porch we worked on had this type of skirt.) While a frameless skirt is easy to install, it's also susceptible to warping and damage because the lattice has very little support. Occasionally, a porch skirting doesn't have a framework and simply consists of a lattice screen attached directly to cleats nailed to the understructure framing. In regions that receive a lot of precipitation, wood rot can begin to appear in less than two years. In time, the parts closest to the ground begin to rot and the decay spreads to the lattice. In older homes, it's often built of untreated pine or fir, neither of which is very resistant to decay and bugs.

#CUTTING VINYL LATTICE PANELS FREE#

This enclosure conceals the framing while it also allows air to circulate under the porch floor, which keeps the framing dry and free of rot.Ī skirt typically consists of a lattice panel set into a wood frame.

#CUTTING VINYL LATTICE PANELS HOW TO#

Here you'll learn how to handle one of the most common of all porch repairs: building a new lattice skirt. If your porch isn't well maintained, the whole house looks shabby.

Cutting vinyl lattice panels